// Router Brand

Sagemcom Router Login

192.168.1.1

Sagemcom Broadband SAS is a French telecommunications equipment manufacturer that produces broadband gateways exclusively for internet service providers. Sagemcom routers are never sold at retail. Every Sagemcom device reaches consumers through an ISP bundle from providers like Windstream, Frontier, SFR, and Orange. The F@ST series is the core product line, with models like the F@ST 5260, F@ST 5366, and F@ST 5655v2 deployed across millions of broadband connections. Default credentials and the IP address vary by ISP, though 192.168.1.1 with admin/admin is the most common configuration.

Sagemcom Broadband SAS, headquartered in France, is a major manufacturer of broadband gateways and set-top boxes for internet service providers worldwide. Unlike consumer brands that sell through retail channels, Sagemcom operates exclusively in the ISP supply chain. If you have a Sagemcom router, your ISP provided it as part of your broadband subscription.

Sagemcom F@ST routers typically use 192.168.1.1 as the default IP address. Open a browser on any device connected to the Sagemcom network and type that address in the address bar. Some Frontier-supplied models use 192.168.254.254 instead, so check the device label if 192.168.1.1 does not load.

The login page displays username and password fields. Enter admin for both on most ISP configurations. Windstream-supplied F@ST 5260 units typically use admin/admin. Frontier and Orange devices may have unique credentials printed on the bottom label.

After logging in, the admin panel shows connection status, Wi-Fi settings, and connected devices. The interface varies between ISP firmware versions.

ISP firmware typically provides two access levels: a basic interface for Wi-Fi and device management, and a restricted admin level for WAN and advanced settings.

Sagemcom Default Credentials by Model

Model	Default IP	Username	Password	Notes
F@ST 5260	192.168.1.1	admin	admin	Windstream, WiFi 5
F@ST 5366	192.168.1.1	admin	(on label)	Frontier, DSL gateway
F@ST 5655v2	192.168.1.1	admin	admin	SFR/Orange, fiber
F@ST 5280	192.168.1.1	admin	admin	Various ISPs, WiFi 5
F@ST 5364	192.168.254.254	admin	(on label)	Frontier, DSL
Livebox 5	192.168.1.1	admin	(on label)	Orange, fiber (Sagemcom-made)

Credentials are ISP-dependent. See the router login guide for additional troubleshooting.

Setting Up a Sagemcom Router

Sagemcom routers arrive pre-configured by your ISP in most cases. If you need to set up the device manually or after a factory reset, follow these steps.

Connect the DSL phone line to the DSL port or the fiber cable to the ONT/WAN port depending on your broadband type. Plug in the power adapter and wait 3-5 minutes. The broadband LED should turn solid green when the connection synchronizes.

Step 1: Connect a computer to the Sagemcom device via Ethernet or the default Wi-Fi network. The SSID and password are printed on the device label.

Step 2: Open a browser and go to 192.168.1.1. Log in with the credentials on the device label.

Step 3: If the internet does not connect automatically, go to the WAN or Internet settings section. ISP-provisioned devices are usually pre-configured via TR-069 remote management. If manual setup is needed, enter the connection type and credentials from your ISP documentation.

Step 4: The Wi-Fi network should be active with the SSID and password printed on the label. Customize these settings if desired.

For ISP-specific setup instructions, contact your provider. Orange customers can find setup guides on the Orange support portal.

Changing Your Sagemcom Wi-Fi Password

Log into the admin panel at 192.168.1.1. Go to Wi-Fi or Wireless in the menu. The exact menu location varies by ISP firmware.

On Windstream F@ST 5260 devices, go to Wi-Fi > Primary Network. On Frontier models, look under Wireless Setup. On Orange Livebox devices, go to My WiFi.

Locate the password or passphrase field. Enter a new password of at least 8 characters. Set the security mode to WPA2-PSK. Click Apply or Save.

The Wi-Fi radio restarts and disconnects all devices. Reconnect with the new password. For general guidance, see the factory reset guide if you need to start fresh.

Sagemcom ISP Integration and F@ST Series Features

Sagemcom F@ST routers are purpose-built for ISP deployment, with features that reflect this specialized role.

TR-069 remote management. ISPs use TR-069 to remotely configure, update firmware, and diagnose Sagemcom devices without requiring a technician visit. This protocol runs in the background and cannot be disabled by the end user.

ISP-specific firmware. Each ISP receives a customized firmware build. A Windstream F@ST 5260 runs entirely different software from a Frontier F@ST 5366. Troubleshooting guides for one ISP version may not apply to another.

Orange Livebox. Sagemcom manufactures the hardware for the Orange Livebox series, one of the most widely deployed broadband gateways in France. The Livebox 5 is a Sagemcom product rebranded with Orange firmware and interface.

Integrated telephony. Many F@ST models include built-in VoIP support with RJ11 phone ports. ISPs configure voice settings through TR-069 during provisioning. The WAN connection handles internet and voice traffic through VLAN separation.

Limited user customization. Users have restricted access to advanced settings. WAN configuration, bridge mode, and VLAN tagging are locked behind ISP-level credentials.

Cannot reach 192.168.1.1. Some Sagemcom models use 192.168.254.254 instead. Check the label on the device for the correct IP address. Verify you are connected to the Sagemcom network via Wi-Fi or Ethernet and not another router in your home. Run ipconfig or ifconfig to confirm your default gateway matches the expected address.
Admin password rejected. ISP-set credentials override the standard admin/admin defaults. Check the label on the bottom of the device for a printed password. Contact your ISP if no label credentials work. Do not attempt to guess ISP super-admin passwords, as multiple failed attempts may lock the account temporarily.
Internet does not reconnect after factory reset. ISP-provisioned settings are erased during a factory reset. Your ISP may need to re-provision the device using TR-069. Contact your ISP and request re-provisioning. Windstream and Frontier support lines can push configuration updates remotely.
Wi-Fi settings page is grayed out. Some ISP firmware locks Wi-Fi configuration behind a different access level. Try logging in with any alternate credentials printed on the device label. On Orange Livebox devices, the Wi-Fi password may only be changeable through the Orange app or customer portal.
Firmware update not available in admin panel. Sagemcom firmware updates are pushed by the ISP through TR-069 and cannot be downloaded manually. Contact your ISP to request the latest firmware push to your device.

// FAQ

Sagemcom Router FAQ

What is the default IP address for Sagemcom routers?

Most Sagemcom F@ST routers use 192.168.1.1 as the default gateway. However, some ISP configurations use different addresses. Certain Frontier-supplied models default to 192.168.254.254 instead. Check the label on your device for the specific IP address your ISP has configured.

What is the default Sagemcom router password?

Default credentials vary by ISP. The most common combination is admin/admin, but ISPs frequently set custom credentials. Windstream typically uses admin/admin. Frontier may use admin with a password printed on the device label. Orange and SFR devices use ISP-specific credentials. Always check the sticker on the bottom of the device first.

Can I buy a Sagemcom router at a store?

No. Sagemcom Broadband SAS manufactures equipment exclusively for ISPs. You cannot purchase a Sagemcom router at retail stores or online retailers. The device is provided as part of your ISP broadband subscription. If you need a replacement, contact your internet service provider.

How do I reset a Sagemcom router to factory settings?

Press and hold the reset button on the back of the device for 15 seconds until the LEDs flash. Release and wait 3-5 minutes for the full reboot. On ISP-supplied devices, a factory reset restores the ISP default configuration. Your ISP may need to re-provision the device after a reset for internet service to resume.

Why are some settings locked on my Sagemcom router?

ISPs restrict access to advanced settings on Sagemcom devices to prevent customers from making changes that could disrupt their network. TR-069 remote management, WAN configuration, and bridge mode are commonly locked. Contact your ISP to request changes to restricted settings.

Which Sagemcom router models are most common?

The F@ST 5260 (Windstream, WiFi 5), F@ST 5366 (Frontier, DSL gateway), F@ST 5655v2 (SFR/Orange, fiber), F@ST 5280 (various ISPs, WiFi 5), and the Orange Livebox 5 (which Sagemcom manufactures for Orange) are the most widely deployed models.