192.168.1.252
192.168.1.252 Router Admin Login
Common static IP for network infrastructure devices near the top of the subnet range.
192.168.1.252 is not a router. It is a device IP address commonly found on IP cameras, wireless access points, managed network switches, and similar infrastructure equipment. If you discovered this address on your network and wondered what it belongs to, it is almost certainly a secondary device, not your main gateway. Your router is at 192.168.1.1 or another gateway address.
Addresses near the top of the subnet, such as .250, .251, .252, and .253, are popular choices for static device assignments. Network administrators and installers place infrastructure devices at these predictable addresses so they can always be found at the same location on the network, regardless of DHCP changes.
Why Devices Use 192.168.1.252
The 192.168.1.x subnet provides 254 usable addresses (.1 through .254). The router typically claims .1 as the gateway. The DHCP server on the router assigns addresses to regular devices (phones, laptops, tablets) from a pool that usually spans .2 through .199 or .2 through .254.
Devices that need permanent addresses are placed outside the DHCP pool at the upper end of the range:
| Address | Common Device |
|---|---|
| 192.168.1.1 | Router (gateway) |
| 192.168.1.2 - .199 | DHCP pool (dynamic devices) |
| 192.168.1.250 | WiFi extender |
| 192.168.1.251 | Network printer |
| 192.168.1.252 | IP camera or access point |
| 192.168.1.253 | WiFi repeater |
| 192.168.1.254 | Secondary router or gateway |
This convention is not a technical requirement. Any device can use any address on the subnet. But organizing static devices at high addresses is a widely followed best practice that prevents conflicts and makes the network easier to manage.
How to Access a Device at 192.168.1.252
Many devices at this address run web-based management interfaces. Open a browser and type 192.168.1.252 in the address bar.
IP cameras. Hikvision cameras show a login page requesting a username and password. The default is usually admin with a password set during initial activation. Dahua cameras use admin/admin on older firmware. Reolink cameras open a live view page after login.
Wireless access points. Ubiquiti UniFi access points show a device information page (though they are typically managed through the UniFi Controller software). TP-Link EAP access points show a standalone management interface. EnGenius access points provide a full web admin panel.
Managed switches. Cisco, Netgear, and TP-Link managed switches provide web interfaces showing port status, VLAN configuration, and traffic statistics.
If the browser returns an error, the device may not have a web interface, may be powered off, or may have moved to a different address. Check your router’s connected devices list to confirm the device’s current IP address.
Identifying the Device at 192.168.1.252
When you see an unfamiliar address on your network, identifying the device takes a few steps.
Check the router’s device list. Log in to your router at 192.168.1.1 and open the connected devices or DHCP clients page. Find 192.168.1.252 in the list. The router displays the device’s hostname (if it reports one) and its MAC address.
Look up the MAC address. Every network device has a unique MAC address. The first three pairs of characters (called the OUI) identify the manufacturer. Run arp -a in Command Prompt to see the MAC address for 192.168.1.252. Search the OUI at an online MAC lookup tool. If the result says “Hikvision,” you have a camera. If it says “Ubiquiti,” you have an access point.
Scan the network. Use a network scanning app like Fing (mobile) or Advanced IP Scanner (Windows). These tools identify device types, manufacturers, and open ports automatically.
Try the address in a browser. If a web interface loads, the page design and branding will tell you what the device is. Camera interfaces look very different from printer pages or switch admin panels.
Troubleshooting 192.168.1.252
-
Cannot reach the device. Verify that your own IP address is in the 192.168.1.x range. If you are on a different subnet, you cannot access 192.168.1.252 without routing between subnets. Also check that the device is powered on and connected to the network.
-
Device keeps losing its address. If the device is set to DHCP instead of a static address, the router may assign it a different IP after a lease renewal. Configure a static IP address directly on the device, or set up a DHCP reservation in the router to lock this address to the device’s MAC address.
-
Two devices sharing the same address. If a camera and an access point are both manually set to 192.168.1.252, both will experience connectivity failures. Assign each device a unique static address. Use .252 for one and .251 or .249 for the other.
-
Admin panel loads but credentials fail. Each device manufacturer uses different default credentials. Check the device label, user manual, or manufacturer’s website. If the password was changed and forgotten, most devices have a physical reset button that restores factory defaults.
-
Cannot find this address on the network. The device may have been reconfigured to a different address, may be on a different VLAN, or may be disconnected. Use a network scanner to search the entire subnet. If the device was moved to a different network, it will not appear on the 192.168.1.x scan.
Device Addresses vs Gateway Addresses
The difference between 192.168.1.252 and 192.168.1.1 is their role on the WAN and LAN network.
192.168.1.1 is the gateway. It routes traffic between your local network and the internet. It runs the DHCP server, DNS forwarder, and firewall. The router login page at this address is where you manage the entire network.
192.168.1.252 is a node on the network. It could be a camera recording video, an access point broadcasting Wi-Fi, or a switch connecting multiple devices. It depends on the router at .1 for internet access and address assignment. It does not control other devices on the network.
If you came here looking for your router, find your router IP address by running ipconfig on Windows or checking Wi-Fi details on your phone. The Default Gateway line shows your router’s address. That is where you go for Wi-Fi passwords, parental controls, and network management.
Frequently Asked Questions
What is 192.168.1.252?
192.168.1.252 is a private IP address commonly assigned as a static address to IP cameras, wireless access points, managed switches, or other network devices. It is not a router gateway. Your router is typically at 192.168.1.1.
Can I access a login page at 192.168.1.252?
Possibly. If the device at this address has a web-based management interface, typing 192.168.1.252 into a browser will open it. IP cameras, access points, and managed switches typically provide browser-based admin panels. Not all network devices have web interfaces.
How do I find out what device is at 192.168.1.252?
Log in to your router at 192.168.1.1 and check the connected devices list. The router shows the hostname and MAC address for each device. You can also run arp -a in Command Prompt to see the MAC address, then search the manufacturer prefix online.
Why is 192.168.1.252 used for static devices?
Addresses near .252, .253, and .254 sit above the typical DHCP pool, which usually ends at .199 or .200. Placing static devices at high addresses prevents conflicts with DHCP-assigned devices and keeps network organization clean.
Can I change the address of a device at 192.168.1.252?
Yes. Access the device's admin panel (either through a browser or its dedicated app) and change the IP address in the network settings. Alternatively, set up a DHCP reservation in your router to assign a different address to the device's MAC address.